再看看启动过程:
OK
U-Boot 1.1.6 (Aug 9 2011 - 07:17:02) For OpenWrt
CPU: S3C6410@666MHz
Fclk = 666MHz, Hclk = 133MHz, Pclk = 66MHz, Serial = CLKUART (ASYNC Mod
e)
Board: MINI6410
DRAM: 256 MB
Flash: 0 kB
NAND: 256 MB
In: serial
Out: serial
Err: serial
MAC: 08:90:90:90:90:90
Hit any key to stop autoboot: 0
#####U-Boot(2011-05, NAND) for Tiny6410#####
Powered by Lintel 2011
[f] Format the nand flash
[v] Download u-boot.bin
[k] Download Linux/Android kernel
[c] Download root cramfs/squashfs image
[j] Download root jffs2 image
[y] Download root yaffs2 image
Download root ubifs image
[a] Download Absolute User Application
[n] Download Nboot.nb0 for WinCE
[w] Download WinCE NK.nb0
[s] Set the boot parameter of Linux
Boot Linux
[q] Quit to shell
NAND(SLC): 256 MiB, RAM: 256 MiB
LCD type, firmware version: 2 1046
Enter your Selection:c
Downloading OpenWrt Rootfs from USB...
OTG cable Connected!
Download address 0xc0000000
Download Done!! Download Address: 0xc0000000, Download Filesize:0x230000
Checksum is being calculated...
Checksum O.K.
Downloading OpenWrt Rootfs successed
Writing OpenWrt Rootfs into NAND...
Erasing at 0x4560000 -- 100% complete.
Writing data at 0x7bf800 -- 100% complete.
Writing OpenWrt Rootfs successed
Saving Environment to NAND...
Erasing Nand...Writing to Nand... done
Linux command line 'root=/dev/mtdblock2 rootfstype=squashfs console=ttySAC0,1152
00' saved
#####U-Boot(2011-05, NAND) for Tiny6410#####
Powered by Lintel 2011
[f] Format the nand flash
[v] Download u-boot.bin
[k] Download Linux/Android kernel
[c] Download root cramfs/squashfs image
[j] Download root jffs2 image
[y] Download root yaffs2 image
Download root ubifs image
[a] Download Absolute User Application
[n] Download Nboot.nb0 for WinCE
[w] Download WinCE NK.nb0
[s] Set the boot parameter of Linux
Boot Linux
[q] Quit to shell
NAND(SLC): 256 MiB, RAM: 256 MiB
LCD type, firmware version: 2 1046
Enter your Selection:OK
U-Boot 1.1.6 (Aug 9 2011 - 07:17:02) For OpenWrt
CPU: S3C6410@666MHz
Fclk = 666MHz, Hclk = 133MHz, Pclk = 66MHz, Serial = CLKUART (ASYNC Mod
e)
Board: MINI6410
DRAM: 256 MB
Flash: 0 kB
NAND: 256 MB
In: serial
Out: serial
Err: serial
MAC: 08:90:90:90:90:90
Hit any key to stop autoboot: 0
NAND read: device 0 offset 0x80000, size 0x500000
........................................Boot with zImage
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Linux version 2.6.36.4 (hu@ubuntu) (gcc version 4.3.3 (GCC) ) #1
PREEMPT Thu Aug 11 22:03:52 CST 2011
[ 0.000000] CPU: ARMv6-compatible processor [410fb766] revision 6 (ARMv7), cr
=00c5387f
[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction ca
che
[ 0.000000] Machine: Mini6410
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] CPU S3C6410 (id 0x36410101)
[ 0.000000] S3C24XX Clocks, Copyright 2004 Simtec Electronics
[ 0.000000] camera: no parent clock specified
[ 0.000000] S3C64XX: PLL settings, A=666000000, M=532000000, E=24000000
[ 0.000000] S3C64XX: HCLK2=266000000, HCLK=133000000, PCLK=66500000
[ 0.000000] mout_apll: source is fout_apll (1), rate is 666000000
[ 0.000000] mout_epll: source is epll (1), rate is 24000000
[ 0.000000] mout_mpll: source is mpll (1), rate is 532000000
[ 0.000000] mmc_bus: source is mout_epll (0), rate is 24000000
[ 0.000000] mmc_bus: source is mout_epll (0), rate is 24000000
[ 0.000000] mmc_bus: source is mout_epll (0), rate is 24000000
[ 0.000000] usb-bus-host: source is clk_48m (0), rate is 48000000
[ 0.000000] uclk1: source is dout_mpll (1), rate is 66500000
[ 0.000000] spi-bus: source is mout_epll (0), rate is 24000000
[ 0.000000] spi-bus: source is mout_epll (0), rate is 24000000
[ 0.000000] audio-bus: source is mout_epll (0), rate is 24000000
[ 0.000000] audio-bus: source is mout_epll (0), rate is 24000000
[ 0.000000] audio-bus: source is mout_epll (0), rate is 24000000
[ 0.000000] irda-bus: source is mout_epll (0), rate is 24000000
[ 0.000000] camera: no parent clock specified
[ 0.000000] s3c64xx: 10485760 bytes SDRAM reserved for fimc at 0x5f5f8000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag
es: 65024
[ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs cons
ole=ttySAC0,115200
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 256MB = 256MB total
[ 0.000000] Memory: 244996k/244996k available, 17148k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] DMA : 0xff600000 - 0xffe00000 ( 8 MB)
[ 0.000000] vmalloc : 0xd0800000 - 0xe0000000 ( 248 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .init : 0xc0008000 - 0xc002a000 ( 136 kB)
[ 0.000000] .text : 0xc002a000 - 0xc0428000 (4088 kB)
[ 0.000000] .data : 0xc0428000 - 0xc044bc20 ( 144 kB)
[ 0.000000] SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, N
odes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU-based detection of stalled CPUs is disabled.
[ 0.000000] Verbose stalled-CPUs detection is disabled.
[ 0.000000] NR_IRQS:246
[ 0.000000] VIC @f4000000: id 0x00041192, vendor 0x41
[ 0.000000] VIC @f4010000: id 0x00041192, vendor 0x41
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] console [ttySAC0] enabled
[ 0.020000] Calibrating delay loop... 665.19 BogoMIPS (lpj=3325952)
[ 0.250000] pid_max: default: 32768 minimum: 301
[ 0.250000] Mount-cache hash table entries: 512
[ 0.250000] CPU: Testing write buffer coherency: ok
[ 0.260000] NET: Registered protocol family 16
[ 0.290000] LEDs initialized.
[ 0.290000] s3c64xx_dma_init: Registering DMA channels
[ 0.290000] s3c64xx_dma_init1: registering DMA 0 (d0808100)
[ 0.300000] s3c64xx_dma_init1: registering DMA 1 (d0808120)
[ 0.300000] s3c64xx_dma_init1: registering DMA 2 (d0808140)
[ 0.310000] s3c64xx_dma_init1: registering DMA 3 (d0808160)
[ 0.310000] s3c64xx_dma_init1: registering DMA 4 (d0808180)
[ 0.320000] s3c64xx_dma_init1: registering DMA 5 (d08081a0)
[ 0.330000] s3c64xx_dma_init1: registering DMA 6 (d08081c0)
[ 0.330000] s3c64xx_dma_init1: registering DMA 7 (d08081e0)
[ 0.340000] PL080: IRQ 73, at d0808000
[ 0.340000] s3c64xx_dma_init1: registering DMA 8 (d080c100)
[ 0.350000] s3c64xx_dma_init1: registering DMA 9 (d080c120)
[ 0.350000] s3c64xx_dma_init1: registering DMA 10 (d080c140)
[ 0.360000] s3c64xx_dma_init1: registering DMA 11 (d080c160)
[ 0.360000] s3c64xx_dma_init1: registering DMA 12 (d080c180)
[ 0.370000] s3c64xx_dma_init1: registering DMA 13 (d080c1a0)
[ 0.370000] s3c64xx_dma_init1: registering DMA 14 (d080c1c0)
[ 0.380000] s3c64xx_dma_init1: registering DMA 15 (d080c1e0)
[ 0.390000] PL080: IRQ 74, at d080c000
[ 0.390000] S3C6410: Initialising architecture
[ 0.440000] bio: create slab <bio-0> at 0
[ 0.450000] SCSI subsystem initialized
[ 0.450000] usbcore: registered new interface driver usbfs
[ 0.450000] usbcore: registered new interface driver hub
[ 0.460000] usbcore: registered new device driver usb
[ 0.460000] s3c-i2c s3c2440-i2c: slave address 0x10
[ 0.470000] s3c-i2c s3c2440-i2c: bus frequency set to 64 KHz
[ 0.470000] s3c-i2c s3c2440-i2c: i2c-0: S3C I2C adapter
[ 0.480000] Advanced Linux Sound Architecture Driver Version 1.0.23.
[ 0.540000] NET: Registered protocol family 2
[ 0.540000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.550000] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.550000] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.560000] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.570000] TCP reno registered
[ 0.570000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.570000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.580000] NET: Registered protocol family 1
[ 0.590000] audit: initializing netlink socket (disabled)
[ 0.590000] type=2000 audit(0.590:1): initialized
[ 0.630000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.630000] Registering mini_fo version $Id$
[ 0.640000] JFFS2 version 2.2 (NAND) (SUMMARY) (ZLIB) (LZO) (LZMA) (RTIME) (R
UBIN) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.650000] msgmni has been set to 478
[ 0.650000] io scheduler noop registered (default)
[ 0.650000] S3C_LCD clock got enabled :: 133.000 Mhz
[ 0.680000] LCD TYPE :: N43 will be initialized
[ 0.680000] Window[0] - FB1: map_video_memory: clear ff600000:0013ec00
[ 0.690000] FB1: map_video_memory: dma=5f200000 cpu=ff600000 size
=0013ec00
[ 0.700000] Console: switching to colour frame buffer device 60x17
[ 0.700000] fb0: s3cfb frame buffer device
[ 0.710000] backlight initialized
[ 1.430000] gpiodev: gpio device registered with major 253
[ 1.430000] gpiodev: gpio platform device registered with access mask FFFFFFF
F
[ 1.440000] adc initialized
[ 1.440000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 1.460000] s3c6400-uart.0: s3c2410_serial0 at MMIO 0x7f005000 (irq = 16) is
a S3C6400/10
[ 1.460000] s3c6400-uart.1: s3c2410_serial1 at MMIO 0x7f005400 (irq = 20) is
a S3C6400/10
[ 1.470000] s3c6400-uart.2: s3c2410_serial2 at MMIO 0x7f005800 (irq = 24) is
a S3C6400/10
[ 1.480000] s3c6400-uart.3: s3c2410_serial3 at MMIO 0x7f005c00 (irq = 28) is
a S3C6400/10
[ 1.490000] S3C NAND Driver, (c) 2008 Samsung Electronics
[ 1.490000] S3C NAND Driver ECC Disabled.
[ 1.490000] NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 2
56MiB 3,3V 8-bit)
[ 1.500000] NAND_ECC_NONE selected by board driver. This is not recommended !
!
[ 1.510000] Creating 3 MTD partitions on "NAND 256MiB 3,3V 8-bit":
[ 1.520000] 0x000000000000-0x000000080000 : "Bootloader"
[ 1.520000] 0x000000080000-0x000000580000 : "Kernel"
[ 1.530000] 0x000000580000-0x000010000000 : "rootfs"
[ 1.580000] mtd: partition "rootfs" set to be root filesystem
[ 1.580000] mtd: partition "rootfs_data" created automatically, ofs=7A0000, l
en=F860000
[ 1.580000] 0x0000007a0000-0x000010000000 : "rootfs_data"
[ 1.640000] dm9000 Ethernet Driver, V1.31
[ 1.760000] eth0: dm9000a at d08da000,d0c00004 IRQ 108 MAC: 08:90:90:90:90:90
(chip)
[ 1.760000] mice: PS/2 mouse device common for all mice
[ 1.770000] touchscreen-1wire initialized
[ 1.770000] backlight-1wire initialized
[ 1.770000] input: TouchScreen Pipe as /devices/virtual/input/input0
[ 1.780000] ts-if initialized
[ 1.780000] S3C24XX RTC, (c) 2004,2006 Simtec Electronics
[ 1.790000] one_wire_status: 4
[ 1.790000] s3c-rtc s3c64xx-rtc: rtc disabled, re-enabling
[ 1.800000] s3c-rtc s3c64xx-rtc: rtc core: registered s3c as rtc0
[ 1.800000] i2c /dev entries driver
[ 1.810000] Linux video capture interface: v2.00
[ 1.810000] [CAM]s3c_fimc_register_controller.id=0
[ 1.810000] s3c_fimc_init_global s3c_fimc.cam_clock=-1069363492
[ 1.820000] s3c-fimc: controller 0 registered successfully
[ 1.820000] [CAM]s3c_fimc_register_controller.id=1
[ 1.830000] one_wire_status: 5
[ 1.830000] s3c-fimc: controller 1 registered successfully
[ 1.840000] s3c-fimc: info ov965x_init
[ 1.840000] [CAM]s3c_fimc_register_camera,cam->id=0
[ 1.850000] s3c_fimc.cam_clock = c042cedc
[ 1.850000] parent clock for camera: 266.000 MHz, divisor: 11
[ 1.860000] [CAM]Reset and init reg!1cam->client=cf01e600
[ 1.860000] [CAM]Reset and init reg!1
[ 1.870000] one_wire_status: 4
[ 1.870000] [CAM]Reset and init reg!2
[ 1.870000] [CAM]s3c_fimc_init_camera[CAM]I2C_CAM_INIT.
[ 1.880000] [CAM]s3c_fimc_init_camera[CAM]s3c_fimc_init_camera[CAM]Reset and
init reg!3
[ 1.890000] one_wire_status: 4
[ 3.150000] S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
[ 3.150000] s3c2410-wdt s3c2410-wdt: watchdog inactive, reset disabled, irq e
nabled
[ 3.150000] cpuidle: using governor ladder
[ 3.160000] sdhci: Secure Digital Host Controller Interface driver
[ 3.160000] sdhci: Copyright(c) Pierre Ossman
[ 3.170000] one_wire_status: 4
[ 3.170000] s3c-sdhci s3c-sdhci.0: clock source 0: hsmmc (133000000 Hz)
[ 3.180000] s3c-sdhci s3c-sdhci.0: clock source 1: hsmmc (133000000 Hz)
[ 3.180000] s3c-sdhci s3c-sdhci.0: clock source 2: mmc_bus (24000000 Hz)
[ 3.190000] one_wire_status: 4
[ 3.200000] mmc0: SDHCI controller on samsung-hsmmc [s3c-sdhci.0] using ADMA
[ 3.200000] s3c-sdhci s3c-sdhci.1: clock source 0: hsmmc (133000000 Hz)
[ 3.210000] s3c-sdhci s3c-sdhci.1: clock source 1: hsmmc (133000000 Hz)
[ 3.210000] s3c-sdhci s3c-sdhci.1: clock source 2: mmc_bus (24000000 Hz)
[ 3.220000] enter s3c64xx_setup_sdhci1_cfg_gpio
[ 3.230000] one_wire_status: 2
[ 3.230000] s3c6400_setup_sdhci_cfg_card: CTRL 2=c0004120, 3=80808080
[ 3.240000] mmc1: SDHCI controller on samsung-hsmmc [s3c-sdhci.1] using ADMA
[ 3.250000] asoc: AC97 HiFi <-> s3c-ac97 mapping ok
[ 3.270000] mmc0: host doesn't support card's voltages
[ 3.270000] mmc0: error -22 whilst initialising SDIO card
[ 3.490000] ALSA device list:
[ 3.490000] #0: MINI6410 (WM9713)
[ 3.500000] TCP westwood registered
[ 3.500000] NET: Registered protocol family 17
[ 3.500000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
[ 3.510000] All bugs added by David S. Miller <davem@redhat.com>
[ 3.520000] s3c-rtc s3c64xx-rtc: setting system clock to 2000-04-10 21:22:18
UTC (955401738)
[ 3.540000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 3.540000] Freeing init memory: 136K
awk: /proc/cpuinfo: No such file or directory
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
jffs2 not ready yet; using ramdisk
[ 11.020000] mini_fo: using base directory: /
[ 11.020000] mini_fo: using storage directory: /tmp/root
- init -
Please press Enter to activate this console. [ 12.860000] eth0: link down
[ 13.200000] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
[ 13.300000] mmc0: Timeout waiting for hardware interrupt.
[ 13.900000] lib80211: common routines for IEEE802.11 drivers
[ 14.390000] Compat-wireless backport release: compat-wireless-2011-04-14
[ 14.390000] Backport based on wireless-testing.git master-2011-04-19
[ 14.800000] cfg80211: Calling CRDA to update world regulatory domain
[ 15.370000] cfg80211: World regulatory domain updated:
[ 15.370000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_g
ain, max_eirp)
[ 15.390000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi,
2000 mBm)
[ 15.390000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi,
2000 mBm)
[ 15.410000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi,
2000 mBm)
[ 15.410000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi,
2000 mBm)
[ 15.430000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi,
2000 mBm)
[ 16.300000] usbcore: registered new interface driver usb8xxx
[ 16.410000] usbcore: registered new interface driver rt2500usb
[ 16.570000] usbcore: registered new interface driver rt73usb
[ 16.670000] usbcore: registered new interface driver rtl8187
[ 16.770000] usbcore: registered new interface driver rt2800usb
[ 17.780000] RPC: Registered udp transport module.
[ 17.780000] RPC: Registered tcp transport module.
[ 17.780000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 18.020000] NTFS driver 2.1.29 [Flags: R/O MODULE].
[ 18.440000] PPP generic driver version 2.4.2
[ 18.860000] usbcore: registered new interface driver p54usb
[ 19.100000] msdos: Unknown symbol fat_dir_empty (err 0)
[ 19.100000] msdos: Unknown symbol fat_time_unix2fat (err 0)
[ 19.120000] msdos: Unknown symbol fat_get_dotdot_entry (err 0)
[ 19.120000] msdos: Unknown symbol fat_free_clusters (err 0)
[ 19.120000] msdos: Unknown symbol fat_setattr (err 0)
[ 19.140000] msdos: Unknown symbol __fat_fs_error (err 0)
[ 19.140000] msdos: Unknown symbol fat_scan (err 0)
[ 19.140000] msdos: Unknown symbol fat_getattr (err 0)
[ 19.160000] msdos: Unknown symbol fat_attach (err 0)
[ 19.160000] msdos: Unknown symbol fat_build_inode (err 0)
[ 19.160000] msdos: Unknown symbol fat_fill_super (err 0)
[ 19.180000] msdos: Unknown symbol fat_alloc_new_dir (err 0)
[ 19.180000] msdos: Unknown symbol fat_remove_entries (err 0)
[ 19.180000] msdos: Unknown symbol fat_add_entries (err 0)
[ 19.200000] msdos: Unknown symbol fat_sync_inode (err 0)
[ 19.200000] msdos: Unknown symbol fat_flush_inodes (err 0)
[ 19.200000] msdos: Unknown symbol fat_detach (err 0)
[ 19.680000] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 19.760000] NET: Registered protocol family 24
[ 19.970000] usbcore: registered new interface driver carl9170
[ 20.250000] usbcore: registered new interface driver usbserial
[ 20.250000] USB Serial support registered for generic
[ 20.280000] usbcore: registered new interface driver usbserial_generic
[ 20.280000] usbserial: USB Serial Driver core
[ 20.480000] Initializing USB Mass Storage driver...
[ 20.480000] usbcore: registered new interface driver usb-storage
[ 20.500000] USB Mass Storage support registered.
[ 20.690000] usbcore: registered new interface driver zd1211rw
[ 20.870000] USB Serial support registered for ch341-uart
[ 20.870000] usbcore: registered new interface driver ch341
[ 21.060000] USB Serial support registered for pl2303
[ 21.060000] usbcore: registered new interface driver pl2303
[ 21.060000] pl2303: Prolific PL2303 USB to serial adaptor driver
[ 21.400000] libertas_sdio: Libertas SDIO driver
[ 21.400000] libertas_sdio: Copyright Pierre Ossman
[ 23.320000] mmc0: Timeout waiting for hardware interrupt.
[ 27.190000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[ 27.190000] jffs2_build_filesystem(): unlocking the mtd device... done.
[ 27.200000] jffs2_build_filesystem(): erasing all blocks after the end marker
...
[ 33.340000] mmc0: Timeout waiting for hardware interrupt.
[ 43.360000] mmc0: Timeout waiting for hardware interrupt.
[ 43.360000] mmc0: Timeout waiting for hardware interrupt.
[ 105.460000] done.
[ 105.460000] JFFS2 notice: (2244) jffs2_build_xattr_subsystem: complete buildi
ng xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0
orphan) found.
[ 105.620000] mini_fo: using base directory: /
[ 105.620000] mini_fo: using storage directory: /overlay
[ 106.010000] s3c2410-wdt s3c2410-wdt: timeout 60 too big
BusyBox v1.15.3 (2011-08-11 20:18:38 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
Backfire (10.03.1-RC5, r13) --------------------------
* 1/3 shot Kahlua In a shot glass, layer Kahlua
* 1/3 shot Bailey's on the bottom, then Bailey's,
* 1/3 shot Vodka then Vodka.
---------------------------------------------------
root@OpenWrt:/#