使用的是qq2440的2.6.13的内核
今天改了一个串口程序：
#include <stdio.h>
#include <string.h>
#include <sys/types.h>
#include <errno.h>
#include <sys/stat.h>
#include <fcntl.h>
#include <unistd.h>
#include <termios.h>
#include <stdlib.h>
int set_opt(int fd,int nSpeed, int nBits, char nEvent, int nStop)
{
struct termios newtio,oldtio;
if ( tcgetattr( fd,&oldtio) != 0) {
perror("SetupSerial 1");
return -1;
}
bzero( &newtio, sizeof( newtio ) );
newtio.c_cflag |= CLOCAL | CREAD;
newtio.c_cflag &= ~CSIZE;
switch( nBits )
{
case 7:
newtio.c_cflag |= CS7;
break;
case 8:
newtio.c_cflag |= CS8;
break;
}
switch( nEvent )
{
case 'O':
newtio.c_cflag |= PARENB;
newtio.c_cflag |= PARODD;
newtio.c_iflag |= (INPCK | ISTRIP);
break;
case 'E':
newtio.c_iflag |= (INPCK | ISTRIP);
newtio.c_cflag |= PARENB;
newtio.c_cflag &= ~PARODD;
break;
case 'N':
newtio.c_cflag &= ~PARENB;
break;
}
switch( nSpeed )
{
case 2400:
cfsetispeed(&newtio, B2400);
cfsetospeed(&newtio, B2400);
break;
case 4800:
cfsetispeed(&newtio, B4800);
cfsetospeed(&newtio, B4800);
break;
case 9600:
cfsetispeed(&newtio, B9600);
cfsetospeed(&newtio, B9600);
break;
case 115200:
cfsetispeed(&newtio, B115200);
cfsetospeed(&newtio, B115200);
break;
default:
cfsetispeed(&newtio, B9600);
cfsetospeed(&newtio, B9600);
break;
}
if( nStop == 1 )
newtio.c_cflag &= ~CSTOPB;
else if ( nStop == 2 )
newtio.c_cflag |= CSTOPB;
newtio.c_cc[VTIME] = 0;
newtio.c_cc[VMIN] = 0;
tcflush(fd,TCIFLUSH);
if((tcsetattr(fd,TCSANOW,&newtio))!=0)
{
perror("com set error");
return -1;
}
printf("set done!\n");
return 0;
}
int open_port(int fd,int comport)
{
char *dev[]={"/dev/tts/0","/dev/tts/1","/dev/tts/2"};
long vdisable;
if (comport==1)
{ fd = open( "/dev/tts/0", O_RDWR|O_NOCTTY|O_NDELAY);
if (-1 == fd){
perror("Can't Open Serial Port");
return(-1);
}
else
printf("open ttyS0 .....\n");
}
else if(comport==2)
{ fd = open( "/dev/tts/1", O_RDWR|O_NOCTTY|O_NDELAY);
if (-1 == fd){
perror("Can't Open Serial Port");
return(-1);
}
else
printf("open ttyS1 .....\n");
}
else if (comport==3)
{
fd = open( "/dev/tts/2", O_RDWR|O_NOCTTY|O_NDELAY);
if (-1 == fd){
perror("Can't Open Serial Port");
return(-1);
}
else
printf("open ttyS2 .....\n");
}
if(fcntl(fd, F_SETFL, 0)<0)
printf("fcntl failed!\n");
else
printf("fcntl=%d\n",fcntl(fd, F_SETFL,0));
if(isatty(STDIN_FILENO)==0)
printf("standard input is not a terminal device\n");
else
printf("isatty success!\n");
printf("fd-open=%d\n",fd);
return fd;
}
int main(void)
{
int fd;
int nread,i;
char buff[]="Hello\n";
if((fd=open_port(fd,1))<0){
perror("open_port error");
return;
}
if((i=set_opt(fd,115200,8,'N',1))<0){
perror("set_opt error");
return;
}
printf("fd=%d\n",fd);
nread=write(fd,buff,8);
printf("nread=%d,%s\n",nread,buff);
close(fd);
return;
}
遇到了以下问题：
fd = open( "/dev/tts/2", O_RDWR|O_NOCTTY|O_NDELAY);
时返回值为3
fcntl(fd, F_SETFL, 0)
返回值为0
isatty(STDIN_FILENO)
返回值为1，这三个函数都正常
但是，到设置参数和读写的时候，也就是从调用tcgetattr( fd,&oldtio)函数开始，就一直不对
后面read，或者write的时候返回值都是-1，
这直接导致串口无法使用
查了很久也不知道什么原因造成的。请高手指点。
